Skip to content
SnapLayer Tools

Volume booster

Make a quiet voice note, lecture or song louder without harsh distortion.

How to use

  1. Drop the quiet recording into the box, or choose it from your phone or computer. MP3, WAV, M4A, OGG and the sound of videos all open.
  2. In the Volume panel, drag the slider above 100 % to make it louder, or press Normalize to let the page find the loudest level that does not clip.
  3. Press Play and switch between Edited and Original to compare. If it sounds harsh or squashed, bring the slider down a little.
  4. Open Export, choose a format, press Export, and download the louder file once you have seen its length and size.

The slider or Normalize

The slider multiplies the volume. At 100 % nothing changes, 200 % is twice as loud in the signal (6 dB more) and 300 % is the most you can ask for, about 9.5 dB. It suits a recording that is quiet all the way through, such as a lecture taken from the back of a hall or a voice note spoken softly.

Normalize does the sum for you. It looks for the loudest single moment in the recording and raises everything until that moment sits just below the top, at −1 dB. It never boosts by more than 30 dB, so a file that is nearly silent does not turn into loud hiss. Because it follows the loudest peak, one sudden bang can stop it lifting the rest much. If Normalize barely changes a recording that still sounds quiet, use the slider with the limiter instead.

Why louder sound can crackle, and what the limiter does

Digital audio has a ceiling. If boosting pushes a peak past it, the top of the wave is flattened, and that flattening is the harsh crackle called clipping. Once a file is clipped the damage is permanent, which is why many volume boosters make a recording louder but also worse.

This one adds a limiter that looks a few milliseconds ahead and turns the sound down just before a peak would go over, then lets it back up smoothly. The loudest moments are held at −1 dB and the rest of the recording stays as boosted. After you export, the page tells you if the limiter had to work hard; then lower the slider a little for a cleaner result.

What louder cannot fix

A boost raises everything, including the hiss, the fan and the room echo, so a noisy recording gets noisier as well as louder. If the voice is hard to follow rather than just quiet, try the Equalizer panel’s Vocal or Podcast preset, which lifts the range speech lives in.

This page saves audio, not video. To make the sound of a video louder, you save the boosted audio as its own file. A recording can be up to about 7 minutes on a phone with little memory, about 27 on most computers and about 54 on larger ones.

Frequently asked questions

How do I make an MP3 louder?

Open the MP3, drag the Volume slider above 100 % or press Normalize, and export it again as MP3. The louder file is a new copy, and your original stays as it was.

How loud can I make it?

The slider goes up to 300 %, which is about 9.5 dB more. Normalize can add up to 30 dB for very quiet files, but it stops as soon as the loudest moment reaches the top.

Will the sound distort if I turn it up too far?

The limiter stops the loudest moments from clipping, so it will not crackle. Very high settings can still sound flat or squashed, because the limiter works harder; if you hear that, bring the slider down.

Is Normalize the same as the slider?

No. The slider applies the amount you choose, while Normalize chooses the amount from the loudest moment in the file. Normalize is quicker, and the slider gives you more control.

Why is my recording still quiet after I boosted it?

It may be that one loud spike sets how far Normalize can go. Use the slider with a higher percentage instead, and let the limiter protect the peak.

Can I make a video louder here?

You can open an MP4 or MOV video, but only its sound is read and you save an audio file. Put the louder audio back into your video with a video editor.

Does boosting the volume reduce the quality?

The boost itself does not, but saving to MP3, M4A or OGG compresses the sound again. At 192 kbps or higher the difference is very hard to hear, and WAV avoids it completely.

Last updated: