Skip to content
SnapLayer Tools

Audio equalizer

Lift the bass, clear up a voice or soften hiss, and hear it before you save.

How to use

  1. Drop a song, voice note or lecture into the box, or choose one from your phone or computer.
  2. In the Equalizer panel, press a preset (Bass boost, Vocal, Treble or Podcast) or drag the ten sliders yourself.
  3. Press Play and switch between Edited and Original while it plays. Adjust the sliders until the Edited sound is the one you prefer.
  4. Open Export, choose a format, press Export, and download your new copy once you have seen its length and size.

What the ten sliders do

Each slider controls one slice of the sound, from the lowest rumble at 31 Hz to the airy top at 16 kHz, and moves it up or down by as much as 12 dB. A rough map helps. The bottom two or three sliders (31 to 125 Hz) are the thump of a kick drum or a bass line. Around 250 to 500 Hz sits the “boxy” or muddy quality of a room. Voices are carried mostly by the sliders from 1 kHz to 4 kHz, and the top ones (8 and 16 kHz) hold hiss, cymbals and the sharp edge of the letter s.

You do not need to learn the numbers. Move one slider while the file plays and listen to what changes, then go back to Edited and Original to check that you made it better rather than just different.

Which preset to start from

Bass boost lifts the lowest four sliders and leaves voices alone, which suits a thin-sounding song, though small phone speakers will not show much of it. Vocal thins the low end and lifts 1 to 4 kHz, where speech is understood, so it helps a muffled interview. Treble adds brightness from 2 kHz upward, for a dull recording.

Podcast is for talking: it cuts the rumble and boominess, lifts the presence of the voice, and softens the hiss above 8 kHz. All presets are gentle on purpose, and you can move any slider afterwards; the panel then says Custom settings. Flat sets every slider to zero, the same as no equalizer.

This changes the file, not your player

Many people search for an equalizer to improve what their phone or music app plays. This page does something different: it makes a new, corrected copy of the file that sounds the same on any device. Your player’s own equalizer is still there, but it stays on for every song, while an edited file is fixed once.

When a slider raises a band, the whole recording can get louder, and the loudest moments might clip. The limiter holds them just under the top, so lift fewer bands, or lower the Volume a little, if the result sounds squashed. The equalizer is applied last, after any cut and volume change.

Frequently asked questions

How do I add more bass to a song?

Press Bass boost, or raise the sliders from 31 to 125 Hz yourself. Check the result through the speaker you use most, since small speakers cannot play the lowest sliders at all.

How do I make a voice recording clearer?

Try the Vocal preset for an interview or the Podcast preset for a talk. If words still blur, raise the 2 kHz and 4 kHz sliders by a few dB.

Can the equalizer remove background noise?

Not really. It can soften steady hiss by lowering the top sliders and cut a low rumble with the bottom ones, but it cannot separate noise from a voice that sits in the same range.

What is the difference between a preset and the sliders?

A preset is a ready-made setting of all ten sliders. When you move any slider afterwards, the panel changes to Custom settings, so you can start from a preset and fine-tune it.

How far can I move a slider?

Up or down by 12 dB. Keep the moves small, a few dB at most, because large boosts add loudness that the limiter then has to hold back.

Will it change the equalizer on my phone or music app?

No. This page edits an audio file and gives you a new copy; your phone’s own settings are not touched, and your original file stays as it was.

Is the sound uploaded for processing?

No. The equalizer runs in your browser, both while you listen and when you export, so the file never leaves your device.

Last updated: